Avaliação de alumina e carvão ativado conjugados com nanopartículas de prata como pré-tratamentos para nanofiltração visando à redução da incrustação / Evaluation of alumina and activated carbon conjugated to silvernanoparticles as nanofiltration pre-treatments aiming at fouling reduction

RESUMO A má distribuição geográfica de águas em território nacional aliada ao seu desperdício, à poluição dos cursos d'água próximos aos centros urbanos e industriais e à eficiência inadequada de processos de tratamento convencionais faz com que o tratamento e o reúso de água sejam tópicos de crescente importância no Brasil. Um dos métodos de tratamento de água são os processos de separação por membranas, como a nanofiltração. No entanto, esses processos estão sujeitos ao fenômeno de incrustação, que provoca diminuição gradativa de sua eficiência. Sendo assim, o presente trabalho visou à avaliação de diferentes métodos de pré-tratamento de água para mitigação da formação de biofilme em membranas de nanofiltração. Os processos de adsorção em partículas de alumina e desinfecção por meio de carvão ativado impregnado com nanopartículas de prata foram aplicados em uma amostra de um corpo d'água superficial. As amostras com e sem pré-tratamento foram nanofiltradas e a propensão à incrustação de cada uma foi avaliada. As eficiências de remoção de compostos orgânicos dos adsorventes empregados separadamente e em conjunto e as análises de absorção UV/Vis, microscópio eletrônico de varredura e espectroscopia de energia dispersiva do carvão ativado impregnado com nanopartículas de prata mostraram que os materiais empregados no pré-tratamento puderam ser apropriadamente sintetizados. Foi possível também identificar os principais grupos funcionais dos biopolímeros presentes nos biofilmes formados ao longo do tempo. Por fim, pôde-se observar que a adsorção da matéria orgânica é mais eficiente para o controle da incrustação rápida, enquanto o efeito bactericida se destaca no controle a longo prazo.

ABSTRACT The poor geographical distribution of water in the national territory combined with its waste, the pollution of watercourses close to urban and industrial centers, and the inadequate efficiency of conventional treatment processes make the treatment and reuse of water topics of increasing importance in Brazil. One of the advanced water treatment methods is membrane separation processes, such as nanofiltration. However, these processes are subject to fouling phenomenon, which causes a gradual decrease in the efficiency of the process. Therefore, the present work aims to evaluate different methods of pretreatment of water to mitigate the formation of biofilm in nanofiltration membranes. The adsorption processes on alumina particles and disinfection through activated carbon impregnated with silver nanoparticles were applied to a sample of a surface water body. Samples with and without pretreatment were nanofiltered and the propensity to fouling was evaluated. The efficiency of the adsorbents, used both separately and together, in removing organic compounds and the UV/Vis, scanning electron microscope, and Energy-dispersive X-ray spectroscopy analyses of the activated carbon impregnated with silver nanoparticles showed that the materials used in the pre-treatment were properly synthesized. It was also possible to identify the main functional groups of the biopolymers present in biofilms formed over time. Finally, it was observed that the adsorption of organic matter is more efficient for the control of rapid fouling while the bactericidal effect stands out in the long-term fouling control.

Remoção de carbono orgânico dissolvido de águas filtradas com tratamento complementar por pré-oxidação com ozônio e adsorção em carvão ativado / Removal of dissolved organic carbon in filtered water complemented with treatment by pre-oxidation with ozone and adsorption on activated carbon

Resumo Este trabalho teve como objetivo avaliar as remoções de carbono orgânico dissolvido presente em águas filtradas de estação de tratamento de água com tratamento complementar por pré-oxidação com ozônio e adsorção em carvão ativado granular. Para o estudo de adsorção foi utilizado o método de ensaio rápido em coluna de escala reduzida, com carvão ativado produzido de cascas de coco. Realizou-se a comparação entre as curvas de ruptura para os ensaios com e sem aplicação de ozônio. Os resultados mostraram reduções nas concentrações de carbono orgânico dissolvido no início dos ensaios e após a passagem da água com e sem pré-ozonização pelas colunas ensaio rápido em coluna de escala reduzida seguida de incrementos progressivos das concentrações à medida que se aumentou o volume de leitos tratados. Na fase final dos ensaios, os aumentos de volume de leitos tratados não causaram mudanças significativas nas concentrações efluentes de carbono orgânico dissolvido. O mesmo comportamento foi observado com relação à absorção em radiação ultravioleta a 254 nm. O uso de ozônio previamente à adsorção em carvão ativado granular, usando o método ensaio rápido em coluna de escala reduzida, resultou em maiores reduções na absorbância da luz ultravioleta em 254 nm do que nas concentrações de carbono orgânico dissolvido. As absorbâncias específicas à radiação ultravioleta das amostras ozonizadas foram menores do que as que não receberam ozônio.

Abstract The objective of this study was to evaluate the removal of dissolved organic carbon in filtered water followed by pre-oxidation with ozone and adsorption on granular activated carbon. The rapid small-scale column test was used for the adsorption essays with activated carbon produced from coconut shells. A comparison was made between the breakthrough curves for tests performed with and without pre-oxidation with ozone. The results showed reductions in dissolved organic carbon concentrations after initial passage of water with and without ozone through the rapid small-scale column test column, followed by progressive increases in concentrations along with the number of the bed volumes. In the final phase of the tests, increases in bed volumes did not cause significative changes in effluent dissolved organic carbon concentrations. The same behavior was also observed with respect to ultra-violet absorbance at 254 nm. The use of ozone prior to adsorption on GAC, using the ERCER method, caused greater reductions on UV254 absorbance than in concentrations of dissolved organic carbon. The specific ultraviolet absorbance values of samples that received ozone were lower than those that were not ozonized.

Reaproveitamento de sabugo de milho para potencial remoção de formulação comercial de glifosato em fase aquosa pela técnica de adsorção / Corn cob reuse in the adsorption of a commercial formulation of glyphosate

RESUMO Neste estudo, foi produzido biocarvão de sabugo de milho ativado com ácido fosfórico (BCA) para potencial remoção do herbicida glifosato — GLF (formulação comercial) em meio aquoso. O BCA foi caracterizado por análises de difração de raios X, espectroscopia de infravermelho, adsorção e dessorção de N2, microscopia eletrônica de varredura e determinação do potencial de carga zero. O efeito do pH inicial e da massa de adsorvente também foi avaliado. Os resultados cinéticos de adsorção foram ajustados aos modelos de pseudoprimeira e pseudossegunda ordem. A natureza do processo foi estudada por meio dos modelos de isoterma de Langmuir e Freundlich, e os parâmetros termodinâmicos calculados para as temperaturas de 23, 43 e 63°C. Os resultados obtidos demonstraram que a adsorção de GLF no BCA foi dependente da temperatura, da massa de adsorvente e do pH do meio, com a melhor condição de ensaio caracterizada por 63°C, 0,25 g de BCA e pH = 7, resultando em boa eficiência de remoção (62,67%), porém com baixa capacidade de adsorção (2,67 mg.g−1). A cinética de adsorção foi representada pelo modelo de pseudossegunda ordem e considerada rápida, sendo necessários 15 min para atingir 98% da capacidade máxima de adsorção. Os dados da isoterma foram bem descritos pelo modelo de Freundlich. Por fim, o estudo termodinâmico revela que a adsorção de GLF é de natureza endotérmica (∆Hº > 0) e endergônica (∆Gº > 0). Os resultados apresentados confirmam que o BCA de sabugo de milho é um adsorvente capaz de remover GLF (formulação comercial) do meio aquoso.

ABSTRACT In this study a biochar was produced from corn cob (BCA), which was activated with phosphoric acid to verify its potential for removal of herbicide glyphosate (GLF) (commercial formula) in aqueous media. BCA was characterized by X-ray diffraction spectroscopy, infrared spectroscopy, sorption and desorption of N2, scanning electron microscope, and zero charge potential. Kinetic results of adsorption were adjusted to pseudo-first and pseudo-second order reactions. The adsorption process was studied to verify if it followed Freundlich and Langmuir isotherms, and the thermodynamic parameter was calculated for 23 oC, 43 cC and 63 oC. The results showed that adsorption of GLF on BCA depended on temperature, adsorbent mass, and pH. The best results were obtained for the temperature of 63 oC with 0.25 g de GLF and pH = 7.0, conditions that presented 62.3% of GLF removal and low adsorption capacity (2.67 mg. g−1). That was probably due to the porous nature of BCA and co-adsorption of other constituents that were present in the commercial formula of GLF. The adsorption kinetics was represented by the model of pseudo-second order and considered fast, taking 15 min to reach 98% of the maximum adsorption capacity. The isotherm data were well represented by the Freundlich model. Finally, the thermodynamic study demonstrated that the adsorption of GLF is of endothermic nature (ΔHº > 0) and endergonic (ΔGº > 0). The results confirmed that BCA from corn cob is an adsorbent capable of removing GLF (commercial formula) from aqueous media. However, the endothermic nature of the process can compromise its performance in water treatment processes.

Materiales carbonosos preparados a partir de cuesco de palma en la adsorción de CO2. Caracterización elemental, próxima y morfológica / Carbonaceous materials prepared from Palm shells for the adsorption of CO2. Elemental, proximal, and morphological characterization / Materiais carbonosos preparados a partir de Cuesco de Palma en a adsorção de CO2. Caracterização elementar, proximal e morfológica

Resumen En la presente investigación se prepararon sólidos porosos tipo carbón activado (CA) a partir de la activación química del cuesco de palma africana procedente de los cultivos de la región de la Guajira, Colombia, con soluciones de Fe(NO3)3 y Cu(NO3)2 con cambio en la concentración a dos diferentes temperaturas: 973 y 1073 K. Los sólidos adsorbentes preparados se caracterizaron para determinar sus propiedades fisicoquímicas y capacidades de adsorción de CO2. Los CA obtenidos presentan micro mesoporosidad con áreas superficiales entre 5 y 1300 m2g-1. Los valores con respecto al contenido de carbono fijo se encuentran entre 47,1 y 78,4%; los resultados evidencian que el proceso de activación tiene efectos sobre los parámetros texturales, composición elemental y proximal de los sólidos obtenidos. También se realizó la caracterización morfológica de la superficie de los materiales con SEM evidenciando la formación de mayor rugosidad en las muestras activadas a 1073 K, específicamente, los carbones activados con el nitrato cúprico; además, mediante EDX se cuantificó la presencia de algunos elementos. Los valores obtenidos de la adsorción de CO2 a bajas presiones se encuentran entre 80 y 250 mg•g-1, evidenciándose una mayor afinidad hacia los sólidos adsorbentes (MCu3 y MFe5).

Abstract In the present investigation, porous solids type activated carbon (CA) were prepared from the chemical activation of the African palm shells from the crops of the Guajira region, Colombia, with solutions of Fe(NO3)3 and Cu(NO3)2 with change in concentration at two different temperatures: 973 and 1073 K. The prepared adsorbent solids were characterized to determine their physicochemical properties and CO2 adsorption capacities. The CAs obtained present micro-mesoporosity with surface areas between 5 and 1300 m2g-1. The values with respect to the fixed carbon content are between 47.1% and 78.4%; the results show that the activation process has effects on the textural parameters, elemental and proximal composition of the solids obtained. The morphological characterization of the surface of the materials was also carried out with SEM, evidencing the formation of greater roughness in the samples activated at 1073 K, specifically, the activated carbons with cupric nitrate; furthermore, the presence of some elements was quantified by EDX. The values obtained from the adsorption of CO2 at low pressures are between 80 and 250 mg•g-1, showing a greater affinity towards adsorbent solids (MCu3 and MFe5).

Resumo Na presente investigação, sólidos porosos do tipo carvão ativado (CA) foram preparados a partir da ativação química do Cuesco de Palma Africana de lavouras da região de Guajira-Colômbia com soluções de Fe(NO3)3 e Cu(NO3)2 com alteração em concentração em duas temperaturas diferentes 973 e 1073 K. Os materiais preparados foram caracterizados para avaliar suas propriedades físico-químicas e capacidades de adsorção de CO2. Os (CAs) obtidos apresentam micro-mesoporosidade com áreas superficiais entre 5 e 1300 m g-1. Os valores com relação ao teor de carbono fixo estão entre 47,1 - 78,4%, os resultados mostram que o processo de ativação tem efeitos nos parâmetros texturais, composição elementar e proximal dos sólidos obtidos. A caracterização morfológica da superfície dos materiais também foi realizada com MEV, evidenciando a formação de maior rugosidade nas amostras ativadas a 1073 K, especificamente os carbonos ativados com nitrato cúprico, e a presença de alguns elementos foi quantificada por EDX. Os valores obtidos na adsorção de CO2 em baixas pressões estão entre 80-250 mg•g-1, mostrando uma maior afinidade para sólidos adsorventes (MCu3 e MFe5).

Content determination of bacteriostats in ocular extractives eye drops and the absorption effect of activated carbon on it / 中国药科大学学报

@#To establish a high performance liquid chromatography(HPLC)method to determine the content of bacteriostats in the ocular extractives eye drops, Diamonsil C18(4. 6 mm×250 mm, 5 μm)column was used, with gradient elusion by 1% triethylamine solution(pH 3. 0)(mobile phase A)and methanol(mobile phase B). The detection wavelength was 256 nm; the column temperature was 40 °C; and the flow rate was 1. 0 mL/min. Under these conditions, the three bacteriostats of methylparaben, ethylparoben and chlorhexidine acetate showed good resolution. The bacteriostats exhibited good linear relationship between the peak area and the concentration in the concentration range of 0. 1- 80 μg/mL(r> 0. 999 1). The recoveries were from 97. 2% to 104. 1%, and the RSD was 0. 8% to 1. 2%. The content of bacteriostats in all the five batches of ocular extractives eye drops was less than 10% of the prescription amount. It was found that the activated carbon used in the production process had strong adsorption effect on the bacteriostat, and that the lower the temperature and the higher the concentration of activated carbon, the stronger the adsorption of bacteriostatic agent. The adsorption capacity of activated carbon for different bacteriostats is: chlorhexidine acetate > ethylparoben > methylparaben. The results showed that the established HPLC method was easy to operate with high sensitivity and good repeatability. It can be used to determine the content of bacteriostat in ocular extractives eye drops quickly and accurately. In addition, this study reveals for the first time the effect of impurity removal process on bacteriostat in the production of ocular extractives eye drops. It is not suitable to use activated carbon to remove impurities before adding parabens and chlorhexidine acetate bacteriostats. The current work provides a new guiding basis for the monitoring and improvement of the quality of ocular extractives eye drops.

Equilibrio, cinética y termodinámica de la adsorción del colorante DB-86 sobre carbón activado de la cáscara de yuca / Equilibrium, kinetic and thermodynamic of direct blue 86 dye adsorption on activated carbon obtained from manioc husk

RESUMEN Objetivo. Establecer mediante experimentos por lote la capacidad de remoción, la cinética y termodinámica de adsorción del carbón activado preparado a partir de la cáscara de yuca (Manihot esculenta) en la remoción del colorante azul directo 86. Materiales y métodos. La metodología experimental consistió inicialmente en la preparación del carbón activado por activación química de la cáscara de yuca con H3PO4 y su posterior calcinación a 530°C. En la caracterización se determinaron las propiedades de textura mediante el índice de yodo e índice de azul de metileno, se cuantificaron los grupos funcionales orgánicos ácidos y básicos con el método Boehm, y se realizó el análisis próximo siguiendo las normas ASTM D-2867-70, ASTM D2866 y ASTM D2866-94. En el estudio por lote, el efecto de varios parámetros sobre la capacidad de adsorción fueron evaluados: el pH (2, 4, 8 y 10), la temperatura (25, 30 y 40°C) y la concentración inicial de colorante (20, 40, 60, 80 y 100 mg/L). Tanto las características fisicoquímicas como los ensayos de adsorción del carbón activado preparado a partir de la cáscara de yuca (CAY) fueron comparadas con otro de marca comercial (CAM). Resultados. Los resultados de la caracterización indican que ambos carbones tienen una química de superfície heterogénea, de naturaleza ácida para el CAY y básica para el CAM. La máxima capacidad obtenida fue 6.1 mg/g para el CAY y de 3.7 mg/g para el CAM. Los cálculos termodinámicos indican que la remoción es espontánea y para ambos carbones la cinética se ajusta al modelo de pseudo segundo orden. Conclusiones. El carbón activado obtenido a partir de la cáscara de yuca puede considerarse un adsorbente eficiente en la remoción de colorantes.

ABSTRACT Objective. To establish by means of experimenting by batch the capacity of removal, the kinetics and adsorption thermodynamics of activated carbon prepared from manioc husk (Manihot esculenta) in the removal of direct blue 86 dye. Materials and methods. Firstly, the experimental methodology worked on the preparation of activated carbon by chemical activation of manioc husk with H3PO4 calcined at 530°C. In the characterization the texture properties were determined by means of the blue methylene and iodine indices, the basic and acidic functional groups were quantified by the Boehm method, and the proximate analyses were done following the norms ASTM D2867-70, ASTM D2866 and ASTM D2866-94. During the batch studies, the effect of several parameters over the adsorption capacity was evaluated: pH (2, 4, 8 and 10), temperature (25, 30 and 40°C) and initial concentration of the dye (20, 40, 60, 80 and 100 mg/L). Both physicochemical and adsorption characteristics of the activated carbon from manioc husk (CAY) were compared against those of a commercial brand (CAM). Results. The results of characterization showed that both carbons have a chemistry heterogeneous surface, acidic for CAY and basic for CAM. The maximum capacity obtained was 6.1 mg/g for CAY and 3.7 mg/g for CAM. The thermodynamic calculations showed that the removal was spontaneous. The kinetics for both carbon samples fits a pseudo second-order model. Conclusions. The activated carbon obtained from the manioc husk can be considered an efficient adsorbent for the removal of dyes.

Production of activated carbon from mango seed coat using chemical activation

Aim: This study was carried out find the feasibility of utilizing raw mango seed coat under various process conditions to produce the best activated carbon by chemical activation and compared with commercial activated carbon. Methodology: Activated carbon was produced by chemical activation under various process conditions such as different activation temperatures, activating agents, impregnation volume percentages and activation times for pyrolysis in a programmable electrical furnace with reactor in the absence of air. Results: The results were compared using phosphoric acid having 50% impregnation volume to other activating agents, the activating temperature was 400oC, activation time 1 hr, iodine number, methylene blue number, % yield and B.E.T surface area being 831 mg g-1, 212 mg g-1, 41.09% and 1114 m2 g-1 respectively. Interpretation: Carbon samples prepared using mango seed coat treated by H3PO4, showed clear open porous structures along with a larger pore size compared to commercially available activated carbon.

Remoção do 2,4-D em amostras de águas pela adsorção em leitos fixos de carvão ativado granular em escala reduzida / Removal of 2,4-D in water samples by adsorption in fixed beds of granular activated carbon on reduced scale

RESUMO O objetivo deste trabalho foi avaliar, por meio dos testes rápidos de coluna em escala reduzida, a capacidade de adsorção do carvão ativado granular (CAG) na remoção do ácido 2,4-diclorofenoxiacético (2,4-D) em amostras de água ultrapura e de água filtrada proveniente de estação de tratamento de água. Os valores da capacidade de adsorção obtidos a partir de amostras de água ultrapura foram 67% superiores aos obtidos para água com presença de matéria orgânica natural (MON). A MON influenciou fortemente a remoção de 2,4-D competindo pelos sítios de adsorção do carvão ativado e diminuiu a capacidade de adsorção para 7,43 mg 2,4-D por grama de CAG. Para a concentração de 2,4-D no afluente igual a 7089 ± 104 µg.L-1 e relação volumeágua/volumeCAG estimado em 766, foi possível produzir água com concentração de 2,4-D inferior a 30 µg.L-1, como recomendado pela Portaria Brasileira de Potabilidade de Água, do Ministério da Saúde (Portaria MS nº 2.914/2011).

ABSTRACT The aim of this study was to assess by means of rapid tests of small-scale column the adsorption capacity of granular activated carbon (GAC) for removal of 2,4-dichlorophenoxyacetic acid (2,4-D) from samples of ultrapure water and filtered water from a water treatment plant. The adsorption capacities values obtained from distilled water samples were 67% higher than those obtained for water having natural organic matter (NOM). NOM strongly influenced the removal of 2,4-D, competing for GAC adsorption sites, and decreasing its adsorption capacity to 7 mg 2,4-D g-1 CAG. For 2,4-D concentration of 7089 ± 104 µg L-1 and the water treated volume/GAC volume at 766, it was possible to produce treated water with 2,4-D concentration less than 30 µg L-1 as recommended by Brazilian Drinking Water Legislation of the Ministry of Health (Portaria MS 2914/2011).

Volatile Chemical Component Differences between Fully and Partially Dried Merbau (Intsia sp.) Wood Using Gas Chromatography-Mass Spectrometry (GC-MS) in Malaysia / Jurnal Sains Kesihatan Malaysia

@#Wood is one of the most common material found in homes and industrial fires, particularly in Malaysia. The abundance of different types of wood used to build structures, frames, furniture and others are important to take note as wood is a conducive material that can be used to initiate and propagate a fire, particularly in forensic fire cases. This study was conducted to provide the volatile chemical fingerprint of burnt Merbau (Intsia sp.) wood using gas chromatographymass spectrometry (GC-MS). The wood samples were prepared under two conditions; fully dried and partially dried. Six study replications of each condition were burnt outdoors and underwent an extraction process using activated carbon tablets. The tablets were incubated in an oven for 16 hours at 80ºC. Next, the tablets were desorbed in two different types of solvent; pentane and ethanol. The pentane- and ethanol-desorbed volatile products were then introduced into the GC-MS. Volatile organic compounds obtained across both conditions were in the range of volatile acids, aromatics and its derivatives, D-glucopyranose, phenolic derivatives and cycloalkane. The compounds emitted by fully and partially dried Merbau wood samples were similar, differing only in the absence of malonic acid and succinic acid in partially dried Merbau wood samples. Both solvents desorbed different types of volatile compounds. The burning behaviour of partially dried Merbau wood were different to those documented from fully dried Merbau wood and is attributed to the composition of wood rather than the dry or wet conditions.

Study on purification effect of formaldehyde in cleanroom by new return air device / 中华劳动卫生职业病杂志

Objective@#To effectively reduce the concentration of poisons in cleanroom, protect the health of workers, realize the optimization and automatic control of the new return air device. And the influence of initial concentration, air volume, temperature and relative humidity of formaldehyde on the purification effect of the new return air device was explored.@*Methods@#The purification effect of the new return air device installed with the activated carbon and the photocatalyst purification net or ordinary activated carbon purification network was tested in a 60 m3 simulated cleanroom. The concentration of formaldehyde was determined by solution absorption-phenol reagent spectrophotometry. Based on the single factor experiment to determine the combination of two purification nets. The effects of air volume, initial formaldehyde concentration, temperature and relative humidity on the purification effect of the new return air device were investigated by orthogonal test. Then, the performance parameters of the return air device to purify formaldehyde were determined.@*Results@#The formaldehyde purification efficiency of the two types of purification nets in the new return air device was higher than that of the ordinary activated carbon purification network (P<0.05) . The combination of activated carbon and photocatalyst purification net has no effect on the formaldehyde purification efficiency of the return air device (P>0.05) . According to the direct analysis and variance analysis, air volume was the most sensitive factor (F value is 18.894, P<0.05) , followed by initial concentration (F value is 16.128, P<0.05) , while temperature and relative humidity have little effect (F value is 0.041 and 0.599, respectively, P>0.05) . LSD analysis showed that there was no significant difference in the purification efficiency of formaldehyde between 475 m3/h and 626 m3/h (P>0.05) . From the perspective of formaldehyde purification efficiency and energy saving, when the air volume is set to 475 m3/h, the new return air device has higher purification efficiency for high concentration of formaldehyde.@*Conclusion@#The new return air device consisting of activated carbon and photocatalyst purification net can play a good purification role in cleanroom with different temperatures and different humidity. Its formaldehyde purification efficiency is affected by air volume and initial concentration.

Study on the effect of activated carbon on formaldehyde in clean workshop / 中华劳动卫生职业病杂志

Objective@#To study the effect of activated carbon on the purification of formaldehyde in the clean workshop return air purification device and its influencing factors.@*Methods@#From May to June 2018, choosed 4 different commercial activated carbons (bamboo charcoal, 1-3 mm, 3-5 mm; coconut shell charcoal, 6-12 mesh, 8-16 mesh) to make 5 types of activated carbon purification net. In the simulated clean plant laboratory, the detection of occupational disease hazards was used to test the purification effect of different types of activated carbon purification nets on formaldehyde.@*Results@#The purification effect of different types of activated carbon increased with the prolongation of purification time, and the difference was statistically significant (P<0.05) . Compared with other types of activated carbon, coconut shell charcoal (8-16 mesh, double layer) had the best purification effect, 15 min and 30 min purification efficiency was 58.72% and 85.20% respectively, and the difference was statistically significant (P<0.05) . The purification effect of double-layer coconut shell charcoal was better than single layer (P<0.05) . The purification effect of double-layer coconut shell charcoal (8-16 mesh) was better than double-layer coconut shell charcoal (6-12 mesh) , the difference was statistically significant (P<0.05) . Coconut shell charcoal (8-16 mesh, double layer) had better purification effect than bamboo charcoal (P<0.05) .@*Conclusion@#Different specific surface area, particle size, and thickness of activated carbon have a certain effect on the purification effect of formaldehyde, and its selection has a certain significance in improving the occupational health protection level in the clean plant, solving the safe use of return air and reducing energy consumption.

Application of activated carbon-decorated polyacrylonitrile nanofibers as an adsorbent in dispersive solid-phase extraction of fluoroquinolones from wastewater / 药物分析学报

A cheap and simple sample preparation method, consisting of a dispersive solid-phase method and an ad-sorbent, activated carbon decorated PAN nanofibers, was employed and used for the extraction of antibiotics (ciprofloxacin, danofloxacin, and enrofloxacin) in wastewater. Electrospun PAN nanofibers that were deco-rated with activated carbon produced from waste tires were used as the solid phase and the antibiotics analyzed by using high-performance liquid chromatography. Parameters such as pH, mass of adsorbent (MA), extraction volume (EV), and extraction time (ET) were optimized owing to their potential effect on the extraction of antibiotics from water. The recovery of all antibiotics was satisfactory, in the range of 90％–99％. The limits of detection and quantification were 0.05, 0.11, 0.20, and 0.53, 1.21, 2.17 μg/L, respectively. The precision was determined from the repeatability and reproducibility and expressed as the intra-day (n = 20) and inter-day (n = 5) precision. The intra-day and inter-day precision was reported in terms of the per-centage relative standard deviation, which was 3％ and 4％, respectively. The adsorption capacity of the ac-tivated carbon-decorated PAN nanofibers was satisfactory, and the reusability of the adsorbent was im-pressive when reused ten times. The accuracy of the dispersive solid phase extraction (DSPE) was validated by spike recovery tests; the results proved the reliability and efficiency of adsorbing antibiotics from was-tewater. Finally, the proposed method was applied to wastewater samples collected from a wastewater treatment plant, which included influent, secondary, and effluent wastewater.

Caracterização e avaliação de fatores que determinam a remoção de microcistina-LR em carvão ativado granular produzido a partir de diferentes matérias-primas / Characterization and evaluation of factors influencing microcystin-LR removal by granular activated carbon produced from different raw materials

RESUMO As microcistinas (MC), que estão entre as cianotoxinas mais encontradas em florações de cianobactérias, não são eficientemente removidas pelas tecnologias do ciclo completo de tratamento de água. Como barreira adicional para sua remoção, destaca-se o processo de adsorção com carvão ativado granular (CAG). Esta pesquisa comparou a eficiência de remoção de MC-LR por sete CAG produzidos a partir de diferentes matérias-primas, analisando as propriedades das amostras: umidade, teor de cinzas, pH e características texturais. Inicialmente, os resultados indicaram que as propriedades dos CAG foram influenciadas pelo material de origem, assim como pelo método de produção. Nos ensaios de adsorção, o modelo de Langmuir indicou que, em quatro horas, com dosagem de 100 mg.L-1, o CAG de linhito (CGLIN) apresentou a maior capacidade de remoção (97,2%) de MC-LR (Co: 115,1 µg.L-1), com qe,máx de 10,6 mg.g-1. O volume de mesoporos influenciou significativamente a capacidade adsortiva de MC dos carvões avaliados (r=0,98, Pearson). Esses resultados podem oferecer subsídios para a aplicação do processo de adsorção de MC-LR em estações de tratamento de água (ETA) para a minimização de intoxicações por água contaminada.

ABSTRACT Microcystins (MC), which are among the cyanotoxins more commonly found in cyanobacterial blooms, are not efficiently removed by full-cycle water treatment technologies. As an additional barrier, there is the adsorption process with granular activated carbon (GAC). This research compared the efficiency of MC-LR removal by seven GACs produced from different raw materials, analyzing these samples' properties: moisture, ash content, pH and textural characteristics. Initially, the results indicated that the GAC properties were influenced by the source material, as well as by the production method. In the adsorption assays, the Langmuir model indicated that in 4h, with 100 mg.L-1 dosage, the granular activated carbon of lignite (CGLIN) had the highest MC-LR (Co: 115.1 µg.L-1) removal capacity (97.2%), with qe,max of 10.6 mg.g-1. The volume of mesopores significantly influenced the adsorption capacity of microcystin by the evaluated GACs (r=0.98, Pearson). These results can support the application of the MC-LR adsorption process in water treatment plants to minimize intoxication with contaminated water.

Adsorción de acetaminofén sobre carbones activados a diferente pH. Entalpía y entropía del proceso / Acetaminophen adsorption on activated carbons at different pH. Change of enthalpy and entropy of the process / Adsorção de acetaminofeno em carvões ativados a diferentes pH. Entalpia e entropia do processo

Resumen Se analizaron los cambios entálpicos y entrópicos derivados del proceso de adsorción de acetaminofén sobre carbones activados con química superficial modificada. Se realizó, además, una variación del pH para determinar los cambios en las propiedades termodinámicas cuando existen cargas en el adsorbato y en el adsorbente. Se encontró que la máxima capacidad de adsorción (1,172 mmoles g-1) corresponde al proceso llevado a cabo en el carbón activado denominado CAR en este estudio a pH 7; los valores de las funciones termodinámicas de entalpía de inmersión y entropía de adsorción fueron -36,02 J g-1 y 0,123 J g-1 K-1, respectivamente. Así, el cambio de entropía de adsorción para el acetaminofén en los carbones activados estudiados dependió del pH. Se encontró que esta función termodinámica varía en el siguiente orden pH 2 > pH 11 > pH 7. Este comportamiento se relaciona con el número de especies presentes en la solución capaces de interactuar con la superficie del carbón activado.

Abstract The enthalpic and entropic changes resulting from the process of acetaminophen adsorption on activated carbons with modified surface chemistry were studied. A pH variation was performed to determine the changes in the thermodynamic properties when there are charges in the adsorbate and adsorbent. It was found that the maximum adsorption capacity (1.172 mmoles g-1) corresponds to the process carried out in the activated charcoal labeled as CAR in this study at pH 7; the values of the thermodynamic functions immersion enthalpy and entropy of adsorption were -36.02 J g-1 and 0.123 J g-1 K-1, respectively. Thus, the adsorption entropy change for the acetaminophen on the activated carbons depended on the pH. It was found that this thermodynamic function varies in the following order pH 2 > pH 11 > pH 7. This behavior is related to the number of species present in the solution capable of interact with the activated carbon surface.

Resumo Foram analisadas as mudanças entrópicas e entalpicas resultantes do processo de adsorção de acetaminofeno sobre carvões activados com superfície química modificada. Além disso, foi realizada uma variação do pH para determinar as alterações nas propriedades termodinâmicas quando existem cargas no adsorbato e no adsorvente. Foi encontrado que a máxima capacidade de adsorção (1.172 mmol g-1) corresponde ao processo realizado no carvão ativado chamado CAR neste estudo em pH 7; os valores das funções termodinâmicas de entalpia de imersão e entropia de adsorção foram -36,02 J g-1 e 0,123 J g-1 K-1 respectivamente. As mudança da entropia de adsorção para o acetaminofeno nos carvões activados dependeu do pH. Foi encontrado que esta função termodinâmica varia na seguinte ordem pH 2 > pH 11 > pH 7. Este comportamento está relacionado ao número de espécies presentes na solução capaz de interagir com a superfície de carvão activado.

Estudio de la adsorción de 4-nitrofenol desde solución acuosa sobre un carbón activado con heteroátomos nitrogenados en la superficie: aplicación del Modelo de Sips / Adsorption study of 4-nitrophenol from aqueous solution on activated carbon with nitrogen heteroatoms on its surface: application of the Sips Model / Estudo da adsorção de 4-nitrofenol a partir de solução aquosa de carvão ativado com heteroátomos azotados na superfície: aplicação do Modelo de Sips

Resumen Se evaluó la aminación de un carbón activado preoxidado con ácido nítrico en la adsorción de 4-nitrofenol. Se aplicó el modelo de Sips a la adsorción desde solución acuosa, utilizando Sigmoidal Logistic 3 Parameter del programa SigmaPlot 12. Los parámetros obtenidos se compararon con los calculados con el programa Statistica 7 para los modelos de Sips y Langmuir. Se encontró que la modificación realizada sobre el carbón activado incrementó la adsorción de 4-nitrofenol de 2,16 a 2,19 mmolg-1, aumentando, a su vez, la afinidad adsorbente-adsorbato. El parámetro para la energía característica del sistema determinado con el modelo de Langmuir toma un valor de 377,47 L mmol-1 al no considerar la heterogeneidad energética, mientras que a partir del modelo de Sips se presenta un valor de 8,32 (Lmmol-1)1/n. Adicionalmente, se encontró que en la ecuación matemática Sigmoidal Logistic 3 Parameter del programa SigmaPlot el valor de 1/x0 corresponde a la constante KLF del modelo Langmuir-Freundlich, mientras que el valor del parámetro Ks del modelo de Sips es igual a (1/x0)-b. Se concluye que la adsorción de 4-nitrofenol sobre el carbón activado se favorece por el incremento de grupos nitrogenados sobre su superficie.

Abstract The amination of a nitric acid pre oxidized activated carbon in the adsorption of 4-nitrophenol was evaluated. The Sips model application to the aqueous solution adsorption data, using Sigmoidal Logistic 3 Parameter formula, in the SigmaPlot 12 program was applied. The obtained parameters were compared with those calculated with Statistica 7 program for Sips and Langmuir models. It was found that the activated carbon increases the adsorption from 2.16 to 2.19 mmol g-1, showing good adsorbent-adsorbate affinity. The system's characteristic energy parameter calculated with the Langmuir model was 377.47 L mmol-1, when not considering energy heterogeneity, while from the Sips model was 8.32 (L.mmol-1)1/n. Additionally, it was found that in the mathematical equation Sigmoidal Logistic 3 Parameter of the SigmaPlot program, the 1/x0 value corresponds to the Langmuir-Freundlich model constant KLF, while the parameter value KS in the Sips model is equal to (1/x0)-b in this program. It was concluded that the 4-nitrophenol adsorption on activated carbon is favored by the presence of nitrogen groups on their activated carbon surface.

Resumo Foi avaliada a aminação de um carvão ativado preoxidado com ácido nítrico na adsorção do 4-nitrofenol. Foi aplicado o modelo de Sips à adsorção desde solução aquosa usando Logística Sigmoidal 3 do programa Sigmaplot 12. Os parâmetros obtidos foram comparados com os calculados com o programa Statistica 7, para os modelos de Sips e Langmuir. Foi encontrado que a modificação do carvão ativado incrementou a adsorção de 4-nitrofenol de 2,16 até 2,19 mmolg-1, acrescentando a afinidade adsorvente-adsorvato. O parâmetro para a energia característica do sistema calculado com o modelo Langmuir teve um valor de 377,47 Lmmol-1 porque não considerou a heterogeneidade energética, enquanto que no modelo de Sips este parâmetro teve um valor de 8,32 (Lmmol-1)1/n. Além disso, foi encontrado que na equação matemática Sigmoidal Logistic 3 Parameter do programa Sigmaplot 3 o valor de 1/x0 corresponde à constante KLF do modelo Langmuir-Freundlich, enquanto o valor do parâmetro KS do modelo de Sips é igual a (1/x0)-b. Conclui-se que a adsorção do 4-nitrofenol sobre carvão ativado é favorecida pela presença de grupos nitrogenado na superfície destes.

Remoção da cor no tratamento combinado de lixiviado de aterro sanitário e esgoto doméstico via processo PACT® / Color removal in the combined treatment of landfill leachate and domestic sewage via PACT ® process

RESUMO Misturas diferentes de lixiviado de aterro sanitário e esgoto doméstico foram aplicadas em 16 reatores em batelada usando o processo PACT® (lodos ativados com adição de carvão ativado em pó - CAP). O objetivo do trabalho foi representar a remoção de cor utilizando dois ajustes matemáticos: o primeiro combinou as variáveis concentração de CAP (0 a 6 g.L-1) e mistura lixiviado/esgoto (0 a 10%, em volume); e o segundo, a concentração de CAP e a cor da mistura (276 a 1.199 uH). A metodologia de superfície de resposta (MSR) foi escolhida para representar a resposta dos ajustes. Os resultados indicaram que, conforme a concentração de lixiviado aumentou até 5%, a adição de CAP resultou em um maior percentual de remoção de cor. No entanto, para a mistura com 10% de lixiviado, os reatores perderam eficácia, com exceção do reator com 6 g.L-1 de CAP, que apresentou os melhores resultados de remoção de cor.

ABSTRACT Sixteen batch reactors fed with different mixtures of landfill leachate combined with synthetic wastewater were treated using the PACT® process (activated sludge process plus powdered activated carbon addition - PAC). The objective was to measure the color removal using two mathematical adjustments: the first adjustment combined the variables PAC concentration (0 to 6 g.L-1) and landfill leachate concentration in the wastewater (0 to 10%, in volume); and the second model combined PAC concentration and the influent color (276 to 1,199 uH). The response surface methodology was used to describe the response of both adjustments. The results indicated that as the proportion of leachate was increased up to 5%, higher PAC concentrations resulted in a better color removal in the reactors. When the leachate proportion was 10%, the reactors were less efficacious, except for the one with 6 g.L-1, which presented the highest color removal within the experiment.

Tratamiento de agua contaminada con metales pesados utilizando como medios filtrantes biorresina intercambiadora de cationes de la cáscara y tallo de guineo y carbón activado de endocarpo de coco / Treatment of contaminated water with heavy metals, utilizing as filtering media a cation exchanger bio-resin from the banana peel and bush and activated carbon from coconut endocarp

En este trabajo de desarrollo experimental, la Escuela de Ingeniería Química de ITCA-FEPADE se propuso comprobar la efectividad de las cáscaras y pseudotallo de guineo y el endocarpo de coco, previamente tratados, para remover la contaminación por metales pesados en una muestra de agua. Para tal objeto, se procesaron dichas biomasas para ser utilizadas como medios filtrantes, los cuales se caracterizaron por medio de pruebas físicas: densidad y tamaño de partícula. Se evaluó su efectividad para remover metales, filtrando agua contaminada con cantidades conocidas de metales pesados tales como hierro, cromo y níquel (Fe3+Cr6+ y Ni2+), variando el tiempo de contacto y el tipo de medio filtrante. La cuantificación de los metales en el agua tratada se llevó a cabo por espectrofotometria de absorción atómica: para el níquel (λ = 232.0 nm); hierro (λ = 24830 nm) y cromo hexavalente (λ = 357.9 nm). Además, se determinó el color en los filtrados por el método de platino-cobalto. Se llegó a la conclusión que las biomasas utilizadas en este estudio resultaron efectivas para la disminución de metales pesados y color en la muestra de agua sintética elaborada en el laboratorio.

In this experimental development work, the Escuela de Ingeniería Química ITCA-FEPADE set out to verify the effectiveness of previously treated banana peels and pseudostem and endocarp to remove heavy metal contamination in a water sample. For this purpose, said biomasses were processed to be used as filter media, which were characterized by means of physical tests: density and particle size. Its effectiveness to remove metals was evaluated, filtering water contaminated with known amounts of heavy metals such as iron, chromium and nickel (Fe3 + Cr6 + and Ni2 +), varying the contact time and the type of filter medium. The quantification of the metals in the treated water was carried out by atomic absorption spectrophotometry: for nickel (λ = 232.0 nm); iron (λ = 24830 nm) and hexavalent chromium (λ = 357.9 nm). In addition, the color in the filtrates was determined by the platinum-cobalt method. It was concluded that the biomasses used in this study were effective in reducing heavy metals and color in the synthetic water sample prepared in the laboratory.

Development of proficiency testing amples of chloroform and carbon tetrachloride activated carbon tubes and their application in inter-laboratory comparison tests / 中国职业医学

OBJECTIVE: To develop proficiency testing samples of chloroform and carbon tetrachloride in activated carbon tubes and analyze their application in inter-laboratory comparison tests in occupational health technical service organizations. METHODS: Three types of mass concentration proficiency testing samples of chloroform and carbon tetrachloride in activated carbon tubes were developed. Their homogeneity and stability were evaluated and the values were determined. The qualified samples were used for inter-laboratory comparison test in occupational health technical service organizations in the country. RESULTS: The prepared chloroform and carbon tetrachloride activated carbon tubes demonstrated good sample homogeneity. There was no significant difference in the measured values of the samples stored at room temperature for one year and the values measured on the day of preparation( P > 0. 05),and the stability was good.Among the 197 institutions participated in the inter-laboratory comparison test of chloroform,the satisfactory result accounted for 86. 29%( 170/197),the problematic results 7. 11%( 14/197),and the unsatisfactory results 6. 60%( 13/197). Among the 195 agencies that participated in the inter-laboratory comparison test of carbon tetrachloride,the satisfactory results accounted for 89. 74%( 175/195),the problematic results 3. 59%( 7/195),and the unsatisfactory results 6. 67%( 13/195). CONCLUSION: The homogenous and stable proficiency testing samples were successfully produced and can be used for inter-laboratory comparison test in occupational health technical service organizations.

Development and validation of an HPLC-UV method for analysis of methylphenidate hydrochloride and loxapine succinate in an activated carbon disposal system / 药物分析学报

Unused medications have the possibility of being abused, causing serious harm to individuals who were not prescribed the drug. The Food and Drug Administration (FDA) recommends the proper disposal of unused prescribed medications to maintain safety and prevent environmental hazards. However, many of the current disposal techniques do not properly address safety. A drug disposal pouch containing granular activated carbon offers a unique disposal method to deactivate residual or expiredmedication in a convenient, effective, and safe manner. A robust and validated method for methylphenidate hydrochloride and loxapine succinate was developed using high-performance liquid chromatography (HPLC) and the deactivation efficiency of the disposal system was tested. Methylphenidate hydrochloride was analyzed on a C18 analytical column (250mm × 4.60mm, 100?) using acetonitrile-water (0.05％ (v/v) trifluoroacetic acid) as the mobile phase at a flow rate of 1.0mL/min with a run time of 15min and retention time of 7.8min. Loxapine succinate was separated on a C8100? (250 mm × 4.6 mm, 5 μm) column maintained at 25 °C using a flow rate of 1.0mL/min. The run time was 10min and the retention time of the drug was around 4.6min.Mobile phase was composed of acetonitrile and water (0.3％ triethylamine) at pH 3.0 as 40:60 (v/v). Reference standard solutions (100 μg/mL) for both drugs were prepared by dissolving in mobile phases. These methods provide good linearity (R2 = 0.999) over the range of 5–100 μg/mL for methylphenidate hydrochloride and 0.1–100 μg/mL for loxapine succinate. The assay methods were successfully applied to study the deactivation of these drugs.

Caracterización de filtros comerciales para agua a base de carbón activado para el tratamiento de agua del río Tumbes - Perú / Characterization of water commercial filters based on activated carbon for water treatment of the Tumbes river - Peru / Caracterização de carvão ativado de filtros comerciais para tratamento da água do rio Tumbes -Perú

Resumen Se caracterizaron y se evaluaron carbones activados comerciales (A, B, C y D) utilizados en filtros para el tratamiento de agua en la descontaminación de metales pesados presentes en agua de río y en la eliminacion de microorganismos coliformes; los carbones comerciales resultaron tener estructuras microporosas y mesoporosas. Se determinaron areas superficiales entre 705 y 906 m2/g. Los carbones fueron amorfos y se detectó la presencia de agentes antibacterianos, tales como Ag, Cl, Cu y Si. Se determinó que para el As y Pb, cuyas concentraciones iniciales en el agua contaminada (agua del Río Tumbes-Perú) fueron 56,7 y 224,0 μg/L, respectivamente, el porcentaje de adsorción fue cercano al 100%. También se encontró que la relación entre el pH de carga cero de los carbones y pH del agua del río durante los experimentos juega un rol determinante en la adsorción de los elementos analizados. Por otro lado, la capacidad antibacteriana fue evaluada satisfactoriamente frente a las siguientes cepas de bacterias gram negativas fecales: Escherichia coli (ATCC® 25922™), Salmonella typhimurium (ATCC® 14028™) y Shigella flexneri (ATCC® 12022™). Esta capacidad se basa en la presencia superficial en los carbones de los agentes antibacterianos mencionados.

Abstract Comercial activated carbon samples (A, B, C, and D) used in filters for the treatment of water were characterized and evaluated in the decontamination of heavy metals present in river water and in the elimination of coliform microorganisms. The carbon samples had microporous and mesoporous structures. Surface areas of between 705 and 906 m2/g were found. The carbon samples were amorphous and the presence of antibacterial agents such as Ag, Cl, Cu, and Si was detected. It was determined that for As and Pb, whose initial concentrations in contaminated water (water of the Tumbes river-Peru) were 56.7 and 224.0 μg/L, respectively, the percentage of adsorption was close to 100%. The relationship between point of zero charge pH of the activated carbons and pH of the river water during the experiments plays a determinant role in the adsorption of the analyzed elements. The antibacterial capacity was evaluated satisfactorily against the following strains of fecal gram negative bacteria: Escherichia coli (ATCC® 25922™), Salmonella typhimurium (ATCC® 14028™), and Shigella flexneri (ATCC® 12022™). This ability is based on the surface presence in the carbons ofthe mentioned antibacterial agents.

Resumo Carvões ativados comerciais (A, B, C e D) usado em filtros para o tratamento de água foram caracterizados e avaliados na descontaminação de metais pesados da água do rio e para a remoção de microrganismos coliformes. Os carvões comerciais mostraram estruturas microporosas e mesoporosas. Foram determinadas as áreas superficiais entre 705 e 906 m2/g. As amostras de carvão foram amorfas e foi detectada a presença de agentes antibacterianos, tais como Ag, Cl, Cu e Si. Determinou-se que, no caso de As e Pb, cujas concentrações iniciais na água contaminada (água do rio Tumbes-Peru) foram de 56,7 e 224,0 μg/L respectivamente, a taxa de adsorção foi de quase 100%. Também foi econtrado que e a relação entre o pH de carga zero dos carvões e o pH da água do rio durante as experiências desempenha um papel decisivo na adsorção dos elementos analisados. Além disso, a capacidade antibacteriana foi avaliada com sucesso contra as seguintes variedades de bactérias gram negativas de origem fecal: Escherichia coli (ATCC® 25922™), Salmonella typhimurium (ATCC® 14028™) e Shigella flexneri (ATCC® 12022™). Esta capacidade esta baseada na presença de agentes bacterianos na superfície dos carvões.