Avaliação da precisão de localização foraminal de um motor endodôntico integrado em diferentes velocidades de rotação / Evaluation of foraminal location accuracy of an integrated endodontic motor employed with different rotational speeds

Objetivo: avaliar a precisão do controle do limite apical de instrumentação do motor endodôntico SENSORY, acionado em três velocidades de rotação (300, 600 e 900 RPM) e função de parada automática apical (Auto Apical Stop - AAS). Material e métodos: sessenta pré-molares inferiores humanos unirradiculados tiveram seus acessos realizados e diâmetro foraminal padronizado em 300 µm. Os dentes foram aleatoriamente divididos em três grupos (n=20) e tiveram seus canais preparados instrumento Logic 30/05, acionado na velocidade predefinida e função AAS ajustada para a marca 0,0. Os instrumentos foram medidos em paquímetro digital e o comprimento real do canal foi aferido pelo método visual direto sob magnificação. Resultados: os valores absolutos dos erros médios e de precisão (±0,5 mm), obtidos foram respectivamente: 0,21 mm e 95% (300 RPM), 0,26 mm e 95% (600 RPM), 0,20 mm e 95% (900 RPM). Não houve diferença significativa entre os grupos (P>0,05). Conclusão: nas condições deste estudo, o uso da função de parada automática forneceu um controle adequado e preciso do limite apical durante a modelagem endodôntica em todas as velocidades testadas.

Objective: to evaluate the accuracy of the control of the apical limit of instrumentation of the SENSORY endodontic motor, activated at three rotation speeds (300, 600 and 900 RPM) and apical automatic stop function (Auto Apical Stop - AAS). Material and methods: Sixty single-rooted human mandibular premolars had their access performed and the foraminal diameter was standardized at 300 µm. The teeth were randomly divided into three groups (n=20) and had their canals prepared with a Logic 30/05 instrument, activated at the predefined speed and the AAS function set to the 0.0 mark. The instruments were measured using a digital caliper and the actual canal length was measured using the direct visual method under magnification. Results: the absolute values of mean and precision errors (±0.5 mm) obtained were respectively: 0.21 mm and 95% (300 RPM), 0.26 mm and 95% (600 RPM), 0.20 mm and 95% (900 RPM). There was no significant difference between groups (P>0.05). Conclusion: Under the conditions of this study, the use of the automatic stop function provided adequate and accurate control of the apical limit during endodontic shaping at all speeds tested.

Effect of open windows on airborne contamination and its topographical distribution in the dental operatory.

Aerosols produced by dental handpieces represent a permanent risk of disease transmission in the dental environment. The current study evaluated the effects of natural ventilation (open windows) on Streptococcus mutans airborne contamination by dental handpieces in simulated clinical conditions. A dental phantom was placed on a dental chair at a standard university dental clinic operatory. An S. mutans suspension was infused into the phantom's mouth while an operator performed standardized dental procedures using low (contra-angle) and high speed (turbine) dental handpieces or an ultrasonic scaler, with windows open or closed. Selective medium Petri dishes were placed in 18 sites of the operatory environment to evaluate contamination topographically. Sites were clustered as: wall, floor, ceiling, dental chair, and cabinet. Contamination was expressed as log10 CFU/cm2 . A linear mixed model analysis was used, nesting the sites within each ventilation and handpiece combination. Open windows significantly reduced contamination. The high-speed handpiece provided the highest contamination, followed by the ultrasonic scaler and the low-speed handpiece. Contamination values were much smaller at the ceiling, and much larger at the chair. Opening windows produced more homogeneous contamination of the operatory compared to closed windows. Natural ventilation during dental procedures decreases contamination and affects its topographical distribution.

Tip and taper compatibility of accessory gutta-percha points with rotary and reciprocating instruments.

Objectives: This study was conducted to evaluate and compare the tip and taper compatibility of accessory gutta-percha points (AGPs) with various rotary and reciprocating instruments. Materials and Methods: Using a profile analyzer, tip and taper measurements were taken of 10 AGPs of each of the 14 models available from Odous de Deus and the 4 models available from Dentsply-Maillefer. Diameter measurements were taken at 1-mm intervals, from 3 mm from the tip (D3) to 16 mm. Results: Based on the mean values obtained, 3-dimensional (3D) models of the AGPs were drawn in Autodesk Fusion 360 and superimposed on 3D models of each instrument selected (Mtwo, Reciproc, RaCe, K3, and ProDesign Logic) to determine the compatibility between the instrument and the AGP. Data corresponding to the tips and tapers of the various AGPs, as well as the tip and taper differences between the AGPs and the instruments, were analyzed using descriptive statistics. The tapers of the AGPs were subject to the American National Standards Institute/American Dental Association No. 57 standard. The Odous de Deus extra-long medium and extra-long extra-medium AGPs were shown to be compatible with Mtwo, K3, and ProDesign Logic instruments with taper 0.06 and tip sizes 25 and 30, while the Dentsply fine and fine medium cones were compatible with Mtwo, RaCe, and K3 instruments with conicity of 0.04 and tip sizes 35 and 40. Conclusions: Both the Odous de Deus and Dentsply commercial brands included 2 AGP models with tip (D3) and taper compatibility with Mtwo, RaCe, K3, and/or Prodesign Logic instruments.

Intensidad lumínica de las lámparas de fotocurado LED en los consultorios odontológicos de Piura, Perú / Output intensity of LED light curing units in dental offices of Piura, Peru

Introducción: La lámpara de fotocurado, que utiliza diodos emisores de luz (LED), se emplea en odontología para la conversión polimérica de los materiales de restauración dental. Se ha comunicado que una intensidad lumínica inadecuada de la lámpara no aseguraría la correcta polimerización del material de restauración. Objetivo: Determinar la intensidad lumínica de las lámparas de fotocurado LED en consultorios odontológicos de la ciudad de Piura, Perú, 2020. Métodos: Estudio observacional, descriptivo. Se midió la intensidad lumínica en 70 lámparas de fotocurado LED, usando un radiómetro con una longitud de onda de 400-500 nm, con capacidad de medida de la intensidad lumínica de hasta 3500 mw/cm2. Por debajo de los 400 mw/cm2 indica intensidad baja, de 400 a 800 mw/cm2 intensidad media, de 800 a 1200 mw/cm2 intensidad alta y por encima de los 1200 mw/cm2 indica intensidad muy alta. Resultados: El 48,5 por ciento de las lámparas analizadas presentaban intensidad media, el 22,86 por ciento intensidad alta, mientras que el 15,71 por ciento intensidad baja y finalmente el 12,86 por ciento de las lámparas presentaban intensidad muy alta. Se reportó menor frecuencia de lámparas con mayor uso clínico. Conclusiones: Las lámparas de fotocurado LED, utilizadas en los consultorios dentales de la provincia de Piura durante el 2020, emiten una intensidad lumínica promedio de 778,14 mW/cm2, equivalente a la intensidad media(AU)

Introduction: Light curing lamps that use light-emitting diodes (LED) are used in dentistry for the polymeric conversion of dental restorative materials. It has been reported that inadequate light intensity in the lamp would not ensure the appropriate polymerization of restorative materials. Objective: Determine the output intensity of LED light curing units used in dental offices of the city of Piura, Peru, in the year 2020. Methods: An observational descriptive study was conducted. Measurements were taken of the light output of 70 LED light curing lamps using a radiometer with a wavelength of 400-500 nm and a light intensity measurement capacity of up to 3 500 mw/cm2. Intensity below 400 mw/cm2 was recorded as low, from 400 to 800 mw/cm2 as medium, from 800 a 1 200 mw/cm2 as high and above 1 200 mw/cm2 as very high. Results: Intensity was medium in 48.5 percent of the lamps analyzed, high in 22.86 percent, low in 15.71 percent and very high in 12.86 percent. A lower frequency of lamps with greater clinical use was reported. Conclusions: The LED light curing lamps used in dental offices of the province of Piura during the year 2020 emit an average output intensity of 778.14 mW/cm2, which corresponds to medium intensity(AU)

Biofilm disruption and bactericidal activity of aqueous ozone coupled with ultrasonic dental scaling.

Background: The COVID-19 pandemic has heightened the awareness of a common hazard encountered in the dental clinic: aerosol transmission of pathogens. Treatment of sources of infection before or during dental procedures is one means of decreasing pathogen load and aerosol transmission. Methods: An ultrasonic scaler supplied with aqueous ozone was used to examine the effect of its viability on planktonic cultures and biofilms formed by 2 model bacteria: Rothia mucilaginosa and Escherichia coli. Results: Both organisms showed susceptibility to aqueous ozone alone (97% and 99.5% lethality, respectively). When combined with manual scaling using an ultrasonic scaler, a greater than 99% reduction in colony-forming units (CFUs)/mL could be reached with an aqueous ozone concentration of approximately 2 mg/L (R. mucilaginosa) or 0.75 mg/L (E. coli) after 5 through 6 seconds of scaling. Conclusions: Aqueous ozone coupled with ultrasonic scaling exhibited a higher efficiency of microbial kill than either method used alone. Both gram-positive and gram-negative species were affected by this treatment. Studies on other oral microbiota constituents, including fungi and viruses, will provide information on the efficacy of this method on a greater biological scale. Studies to verify concomitant reduction of microbial load in dispersed aerosols in clinical settings should be completed to support practical applications of this treatment.

Evaluation of a protocol for reducing the microbial contamination of dental unit water.

Biofilm on dental unit waterlines can spread microbial contamination in the water. The aim of this study was to investigate microbial contamination of water from supplies and dental units before and after the implementation of a protocol for microbial quality improvement and maintenance of dental unit water. The microbial load was evaluated in water from 27 taps and dental units (reservoirs, air-water syringes and highspeed outputs without handpieces) using the PetrifilmT system (total aerobic bacteria and fungi) and conventional culture media (enterobacteria and Legionella spp.). The bacterial load in water samples from taps and reservoirs was within the parameter established by Brazilian legislation (<500CFU/mL); but the bacterial load in samples from air-water syringes and high-speed outputs without handpieces was not. The implementation of the protocol for the maintenance of microbial quality in dental unit water reduced bacterial load in highspeed outputs without handpieces (p=0.004). Enterobacteria and Legionella spp. were not isolated from any of the water samples from taps and dental units.

Biofilme nas linhas d\'água de equipos odontológicos pode propagar contaminando microbiana na água. O objetivo deste estudo foi investigar a contaminando microbiana da água de abastecimentos e equipos odontológicos antes e após a implementando de um protocolo para melhoria e manutenndo da qualidade microbiològica da água de equipos dontológicos. Avaliou-se a carga microbiana da água de 27 torneiras e equipos (reservatórios, seringas tríplice e alta rotando sem as penas de mdo) de uma clínica odontológica por meio do sistema PetrifilmT (bacterias aeróbias totais e fungos) e meios de cultura convencionais (enterobactérias e Legionella spp.). A carga bacteriana em amostras de água das torneiras e reservatórios estava dentro do paràmetro estabelecido pela legislando brasileira (<500 UFC/mL), mas a carga bacteriana das seringas tríplices e das saídas dos alta rotando sem as penas de mdo ndo estava. A implementando do protocolo para manutenndo da qualidade da água dos equipos reduziu a carga bacteriana nas saídas dos alta rotando sem as penas de mdo (p=0,004). Enterobactérias e Legionella spp. ndo foram isoladas de qualquer das amostras de água das torneiras e dos equipos odontológicos.

Evaluation of a protocol for reducing the microbial contamination of dental unit water

Biofilm on dental unit waterlines can spread microbial contamination in the water. The aim of this study was to investigate microbial contamination of water from supplies and dental units before and after the implementation of a protocol for microbial quality improvement and maintenance of dental unit water. The microbial load was evaluated in water from 27 taps and dental units (reservoirs, airwater syringes and highspeed outputs without handpieces) using the Petrifilm™ system (total aerobic bacteria and fungi) and conventional culture media (enterobacteria and Legionella spp.). The bacterial load in water samples from taps and reservoirs was within the parameter established by Brazilian legislation (<500CFU/mL); but the bacterial load in samples from airwater syringes and highspeed outputs without handpieces was not. The imple mentation of the protocol for the maintenance of microbial quality in dental unit water reduced bacterial load in highspeed outputs without handpieces (p=0.004). Enterobacteria and Legionella spp. were not isolated from any of the water samples from taps and dental units (AU)

Biofilme nas linhas d'água de equipos odontológicos pode propagar contaminação microbiana na água. O objetivo deste estudo foi investigar a contaminação microbiana da água de abastecimentos e equipos odontológicos antes e após a implemen tação de um protocolo para melhoria e manutenção da qualidade microbiológica da água de equipos odontológicos. Avaliouse a carga microbiana da água de 27 torneiras e equipos (reservatórios, seringas tríplice e alta rotação sem as peças de mão) de uma clínica odontológica por meio do sistema Petrifilm™ (bactérias aeróbias totais e fungos) e meios de cultura convencionais (enterobactérias e Legionella spp.). A carga bacteriana em amostras de água das torneiras e reservatórios estava dentro do parâmetro estabelecido pela legislação brasileira (<500 UFC/mL), mas a carga bacte riana das seringas tríplices e das saídas dos alta rotação sem as peças de mão não estava. A implementação do protocolo para manutenção da qualidade da água dos equipos reduziu a carga bacteriana nas saídas dos alta rotação sem as peças de mão (p=0,004). Enterobactérias e Legionella spp. não foram isoladas de qualquer das amostras de água das torneiras e dos equipos odontológicos (AU)

Analysis of cutting capacity, preparation time, and apical deviation after instrumentation of artificial curved canals with the waveone ® and reciproc ® reciprocating systems / Análise da capacidade de corte, tempo de prepare e desvio apical após a instrumentação de canais curvos artificiais com sistemas reciprocantes Waveone ® e Reciproc ®

ABSTRACT Objective To analyze cutting capacity, preparation time, and occurrence of apical deviation, after instrumentation of curved canals with reciprocating Primary WaveOne ® and R25 Reciproc ® systems. Methods Twenty simulated canals with 35° bends were randomly assigned to the Primary WaveOne ® or R25 Reciproc ® . The preparations were made by a single operator. The cutting capacity was assessed by the difference in weight (on an analytical balance) of the canals before and after preparation. The time needed for the preparation was analyzed. The canals were filled with India ink and photographed on a platform before and after the preparation to analyze the apical deviation to a 1 mm length. The images were superimposed in Photoshop ® and the measurement was performed with the ruler tool. Statistical analysis was performed using Student's t-test. The level of significance was set at 5%. Results The WaveOne ® Primary system was more effective (in terms of cutting capacity) but had a longer preparation time than the R25 Reciproc ® instrument. Apical deviation was the only variable that did not significantly differ between the two systems. Conclusion The WaveOne ® Primary had a higher cutting capacity than the R25 Reciproc ® . Both systems maintained the original canal path. The preparation time was shorter for the R25 Reciproc ® than the WaveOne ® Primary system.

RESUMO Objetivo Analisar a capacidade de corte, o tempo de preparo e a ocorrência de desvio apical, após a instrumentação de canais curvos com os sistemas reciprocantes WaveOne ® e Reciproc ® . Métodos Vinte canais simulados, com 35° de curvatura, foram randomicamente divididos para os dois sistemas. Os instrumentos utilizados foram o WaveOne ® Primary e o R25 Reciproc ® . Cada instrumento foi utilizado em um canal. Os preparos foram feitos por um único operador. Para análise da capacidade de corte, os canais foram pesados em balança analítica antes e após o preparo. A diferença na pesagem foi utilizada para aferição. O tempo para execução do preparo foi cronometrado e os valores obtidos foram analisados. Já para análise do desvio a 1 mm do comprimento de trabalho, antes e após o preparo, os canais foram preenchidos com tinta nanquim e fotografados em uma plataforma. As imagens foram sobrepostas no Photoshop ® e, com a ferramenta régua, foi realizada a medição. Resultados Para análise estatística foi utilizado o teste T de Student, com nível de significância de 5%. Na análise da capacidade de corte, o sistema WaveOne ® Primary foi mais eficaz que o instrumento R25 Reciproc ® , embora o seu tempo de preparo tenha sido maior. Apenas no critério, desvio apical, não se verificou diferença significativa entre os dois sistemas. Conclusão O WaveOne ® Primary apresentou uma maior capacidade de corte que o R25 Reciproc ® . Ambos os sistemas respeitaram a trajetória original do canal. O tempo de preparo do R25 Reciproc ® foi menor que o WaveOne ® Primary.

Electromagnetic interference of dental equipment with implantable cardioverter defibrillators.

OBJECTIVE: Implantable cardioverter defibrillators (ICDs) are subject to electromagnetic interference (EMI). The aim of this study was to assess both the EMI of dental equipments with ICDs and related factors. MATERIALS AND METHODS: High- and low-speed handpieces, an electric toothbrush, an implant motor and two types of ultrasonic devices were tested next to an ICD with different sensitivity settings. The ICD was immersed in a saline solution with electrical resistance of 400-800 ohms to simulate the resistance of the human body. The dental equipments were tested in both horizontal (0°) and vertical (90°) positions in relation to the components of the ICD. The tests were performed with a container containing saline solution, which was placed on a dental chair in order to assess the cumulative effect of electromagnetic fields. RESULTS: The dental chair, high- and low-speed handpieces, electric toothbrush, implant motor and ultrasonic devices caused no EMI with the ICD, irrespective of the program set-up or positioning. No cumulative effect of electromagnetic fields was verified. CONCLUSIONS: The results of this study suggest that the devices tested are safe for use in patients with an ICD.

Atendimento odontológico: eficácia do treinamento e requisitos dos equipamentos para reduzir riscos ergonômicos / Dental care: efficacy of training and equipment requirements to reduce ergonomic risks

Este estudo teve por objetivo verificar a eficácia de um treinamento ergonômico na diminuição de posturas inadequadas adotadas por cirurgiãs-dentistas durante a execução de procedimentos de raspagem periodontal. Sessenta (60) cirurgiãs-dentistas foram alocadas aleatoriamente em dois grupos: o grupo de intervenção - G1, composto por 22 profissionais que receberam instruções e treinamento ergonômico teórico e prático; o grupo controle - G2, composto por 38 profissionais receberam o mesmo treinamento apenas após ao final do estudo. No baseline, utilizou-se um manequim odontológico no qual todas as participantes realizaram procedimentos de raspagem e alisamento dental em 6 faces dentárias, uma em cada sextante: faces vestibulares dos dentes 16, 11, 26 e 31 e faces linguais dos dentes 36 e 46. As observações foram realizadas através de vídeos realizados com 5 câmeras digitais, fixadas num suporte especificamente construído para obtenção de diferentes ângulos de visualização: direita, esquerda, posterior, superior e geral. Realizou-se análise exploratória da distribuição dos dados seguida de análise descritiva e analítica utilizando-se o teste de ANOVA de medidas repetidas com =5%. Foram realizadas 984 análises das quais 720 antes do treinamento e 264 após o treinamento. O treinamento ergonômico possibilitou 63% de redução de prevalência de posturas não recomendadas e houve diferença estatisticamente significante (p<0,00001) entre os grupos controle (inicial e final), intervenção inicial e intervenção final. Concluiu-se que o treinamento ergonômico realizado contribuiu significativamente para diminuir a prevalência de posturas não recomendadas durante a execução de procedimentos básicos periodontais.(AU)

This study aimed to assess the efficacy of an ergonomic training in order to decrease the prevalence of not recommended postures assumed by dentists during dental scaling procedures. Sixty (60) female dentists were randomly allocated into two groups: G1- intervention group - composed by 22 dentists who received theoretical and practical ergonomic training; G2 - control group - composed by 38 professionals received the similar training only after the end of the study. In the baseline, it was used a dental manikin in which all participants performed dental scaling on 6 dental surfaces, one in each sextant of the mouth: buccal surfaces of 16, 11, 26 and 31 teeth and lingual faces of 36 and 46 teeth. The observations were made through videos realized with 5 digital cameras, fixed in a support specifically constructed to obtain different viewing angles: right, left, posterior, superior and general. An exploratory analysis of the data distribution followed by descriptive and analytical analysis was performed using the ANOVA test for repeated measures with = 5%. A total of 1440 observations were performed, 720 before and 720 after training. Ergonomic training decrease the prevalence of not recommended postures in 63%. There was a statistically significant difference (p <0.00001) between the control, pre-training intervention and post-training intervention groups. It was concluded that the ergonomic training was effective to decrease the prevalence of not recommended postures during dental scaling procedures.(AU)

Assessment of the Centralization of Root Canal Preparation with Rotary Systems.

OBJECTIVE: Apical deviations are important factors in endodontic therapy, since they can cause the treatment failure. The aim of the present study was to determine the centering capacity of ProTaper Universal™, Twisted File™ and Revo-S® rotary systems using cone beam computed tomography analysis before and after the instrumentation of root canals. MATERIALS AND METHODS: Thirty mesiobuccal roots from human lower first molars were divided into three groups of ten: Group 1 - ProTaper Universal™ Rotary System; Group 2 - Twisted File™ Rotary System; and Group 3 - Revo-S® Rotary System. All teeth were scanned using computed tomography to determine the condition of the root canal before and after instrumentation (4mm, 3mm and 2mm from the root apex). Images were made using ICAT VISION software for both instrumented and non-instrumented canals. RESULTS: The results were analyzed statistically using the Kolmogorov-Smirnov normality test for quantitative variables. Comparisons were made with two groups (Mann-Whitney - abnormal) and with more than two groups (Kruskal Wallis - abnormal). The level of significance was set at p<0.05. A statistically significant difference was found for the measurement of 4 mm between the "ProTaper Universal" and "Twisted File" systems. For the Twisted File system, a statistically significant difference was recorded between the measurements of 4mm and 3 mm. CONCLUSION: None of the assessed instruments was completely effective in terms of the biomechanical preparation of root canals since all created deviation from the original anatomy of the canal.

Eficácia de três substâncias desinfetantes na prática da radiologia odontológica / Effectiveness of three substances disinfectants in dental radiology practice

O estudo avaliou prevalência bacteriana em componentes utilizados na Radiologia Odontológica e testou a eficácia de três substâncias desinfetantes. Foram avaliadas quatro superfícies em quatro clínicas (cilindro localizador, avental de chumbo, disparador de raios X e câmara escura), sendo testados: álcool 70%, hipoclorito de sódio 2,5% e ácido peracético 0,2%. Foram utilizados os métodos bioquímicos de identificação. Em 91,7% das superfícies analisadas, houve contaminação bacteriana, sendo Staphylococcus o gênero mais prevalente, seguido dos bacilos gram-positivos. O hipoclorito de sódio 2,5% e o ácido peracético 0,2% reduziram a contaminação bacteriana de 93,8% para 6,3%, enquanto o álcool 70% reduziu de 87,5% para 56,3%, após o seu uso.

The study aimed to evaluate bacterial prevalence of dental radiology equipment and to test the effectiveness of 03 disinfection substances. 04 Surfaces were evaluated in 04 clinical (locating cylinder, lead apron, trigger X-ray and darkroom) being tested: Alcohol 70%, sodium hypochlorite 2.5% and 0.2% peracetic acid. Biochemical methods have been used for identification. In 91.7% of the areas examined were bacterial contamination, the most prevalent being Staphylococcus genus, followed by gram-positive bacilli. The 2.5% sodium hypochlorite and 0.2% peracetic acid reduced the bacterial contamination of 93.8% to 6.3%, while the 70% ethanol showed only 31.2% of bacterial absence after use.

Accuracy of intraoral and extraoral digital data acquisition for dental restorations

ABSTRACT The computer-aided design (CAD) and computer-aided manufacturing (CAM) process chain for dental restorations starts with taking an impression of the clinical situation. For this purpose, either extraoral digitization of gypsum models or intraoral digitization can be used. Despite the increasing use of dental digitizing systems, there are only few studies on their accuracy. Objective This study compared the accuracy of various intraoral and extraoral digitizing systems for dental CAD/CAM technology. Material and Methods An experimental setup for three-dimensional analysis based on 2 prepared ceramic master dies and their corresponding virtual CAD-models was used to assess the accuracy of 10 extraoral and 4 intraoral optical non-contact dental digitizing systems. Depending on the clinical procedure, 10 optical measurements of either 10 duplicate gypsum dies (extraoral digitizing) or directly of the ceramic master dies (intraoral digitizing) were made and compared with the corresponding CAD-models. Results The digitizing systems showed differences in accuracy. However, all topical systems were well within the benchmark of ±20 µm. These results apply to single tooth measurements. Conclusions Study results are limited, since only single teeth were used for comparison. The different preparations represent various angles and steep and parallel opposing tooth surfaces (incisors). For most digitizing systems, the latter are generally the most difficult to capture. Using CAD/CAM technologies, the preparation angles should not be too steep to reduce digitizing errors. Older systems might be limited to a certain height or taper of the prepared tooth, whereas newer systems (extraoral as well as intraoral digitization) do not have these limitations.

Fungal contamination and disinfection of dental chairs, Teresina, Piaui, Brazil.

The aim of this study was to analyze fungal contamination on dental chairs at the clinic of a Higher Education Institution in TeresinaPI, Brazil, and to evaluate the effectiveness of different disinfectants: 70% alcohol and 1% sodium hypochlorite. We selected the five sites with most contact between patient and chair: headrest, backrest, armrests, seat and foot rest. Samples were collected from these sites on 14 chairs and inoculated in agar Sabouraud culture medium containing chloramphenicol. Pathogenic fungi were isolated from all sampling sites on the chairs. Highest frequencies were found on footrest, followed in decreasing order by seat, backrest, armrests and headrest. Fourteen species of filamentous fungi were identified, belonging to the genera Alternaria, Aspergillus, Cladosporium, Curvularia, Drechslera, Fusarium, Penicillium and Paecillomyces. After sampling, seven chairs were disinfected with 70% alcohol and seven with 1% sodium hypochlorite, and samples were taken again using the same procedure. No fungal growth was detected following disinfection with sodium hypochlorite, which was clearly more effective than alcohol, after which there was still fungal growth. This study highlights the need for the biosafety protocol to include cleaning and disinfection of dental chairs with 1% sodium hypochlorite after each attendance in order to prevent crossinfection.

O objetivo deste estudo foi analisar contaminação fúngica em cadeiras odontológicas na clínica de uma Instituição de Educação Superior em Teresina PI, Brasil, e avaliar a efetividade de diferentes desinfetantes: álcool 70% e hipoclorito de sódio 1%. Nós selecionamos os cinco locais com maior contato entre o paciente e a cadeira: encosto da cabeça, das costas, dos braços, assento e encosto dos pés. As amostras foram coletadas destes locais das 14 cadeiras e inoculadas em meio de cultura agarSabouraud contendo cloranfenicol. Fungos patogênicos foram isolados de todos os locais de amostragem das cadeiras. As frequências mais altas foram encontradas no encosto dos pés, seguido em ordem decrescente pelo assento, encosto das costas, dos braços e encosto da cabeça. Quatorze espécies de fungos filamentoso foram identificados, pertencente aos gêneros Alternaria, Aspergillus, Cladosporium, Curvularia, Drechslera, Fusarium, Penicillium e Paecillomyces. Após a coleta, sete cadeiras foram desinfetadas com álcool 70% e sete com hipoclorito de sódio 1%, e as amostras foram colhidas novamente usando o mesmo procedimento. Não foi detectado crescimento fúngico após desinfecção com hipoclorito de sódio, que foi claramente mais efetivo que o álcool, do qual ainda houve crescimento fúngico. Este estudo destaca a necessidade da inclusão no protocolo de biossegurança a limpeza e desinfecção das cadeiras odontológicas com o hipoclorito 1% após cada atendimento, a fim de prevenir infecções cruzadas.

Fungal contamination and disinfection of dental chairs, Teresina, Piauí, Brazil / Contaminação de fungos e desinfecção em cadeiras odontologicas, Teresina, Piauí, Brasil

The aim of this study was to analyze fungal contamination on dental chairs at the clinic of a Higher Education Institution in TeresinaPI, Brazil, and to evaluate the effectiveness of different disinfectants: 70% alcohol and 1% sodium hypochlorite. We selected the five sites with most contact between patient and chair: headrest, backrest, armrests, seat and foot rest. Samples were collected from these sites on 14 chairs and inoculated in agar Sabouraud culture medium containing chloramphenicol. Pathogenic fungi were isolated from all sampling sites on the chairs. Highest frequencies were found on footrest, followed in decreasing order by seat, backrest, armrests and headrest. Fourteen species of filamentous fungi were identified, belonging to the genera Alternaria, Aspergillus, Cladosporium, Curvularia, Drechslera, Fusarium, Penicillium and Paecillomyces. After sampling, seven chairs were disinfected with 70% alcohol and seven with 1% sodium hypochlorite, and samples were taken again using the same procedure. No fungal growth was detected following disinfection with sodium hypochlorite, which was clearly more effective than alcohol, after which there was still fungal growth. This study highlights the need for the biosafety protocol to include cleaning and disinfection of dental chairs with 1% sodium hypochlorite after each attendance in order to prevent crossinfection.

O objetivo deste estudo foi analisar contaminação fúngica em cadeiras odontológicas na clínica de uma Instituição de Educação Superior em TeresinaPI, Brasil, e avaliar a efetividade de diferentes desinfetantes: álcool 70% e hipoclorito de sódio 1%. Nós selecionamos os cinco locais com maior contato entre o paciente e a cadeira: encosto da cabeça, das costas, dos braços, assento e encosto dos pés. As amostras foram coletadas destes locais das 14 cadeiras e inoculadas em meio de cultura agarSabouraud contendo cloranfenicol. Fungos patogênicos foram isolados de todos os locais de amostragem das cadeiras. As frequências mais altas foram encontradas no encosto dos pés, seguido em ordem decrescente pelo assento, encosto das costas, dos braços e encosto da cabeça. Quatorze espécies de fungos filamentoso foram identificados, pertencente aos gêneros Alternaria, Aspergillus, Cladosporium, Curvularia, Drechslera, Fusarium, Penicillium e Paecillomyces. Após a coleta, sete cadeiras foram desinfe tadas com álcool 70% e sete com hipoclorito de sódio 1%, e as amostras foram colhidas novamente usando o mesmo procedimento. Não foi detectado crescimento fúngico após desinfecção com hipoclorito de sódio, que foi claramente mais efetivo que o álcool, do qual ainda houve crescimento fúngico.Este estudo destaca a necessidade da inclusão no protocolo de biossegurança a limpeza e desinfecção das cadeiras odontológicas com o hipoclorito 1% após cada atendimento, a fim de prevenir infecções cruzadas.

Interferência eletromagnética dos equipamentos odontológicos nos dispositivos cardíacos eletrônicos implantáveis / Electromagnetic interference of dental equipment in cardiovascular implantable electronic devices

Os dispositivos cardíacos eletrônicos implantáveis (DCEI) são rotineiramente utilizados no tratamento de doenças cardiovasculares, especialmente na população idosa. Estes dispositivos estão sujeitos à interferências eletromagnéticas (IEM) provocadas por equipamentos eletrônicos. Desta forma, este estudo objetivou avaliar a IEM causada por equipamentos odontológicos nos DCEI (marcapasso ­ MP e desfibrilador cardíaco implantável ­ DCI). Para tanto, foram delineados três artigos científicos: uma revisão sistemática da literatura e dois estudos in vitro. Para a revisão sistemática foi realizada buscas em bases de dados eletrônicas, por meio de descritores, para a identificação de estudos potencialmente relevantes. Foram incluídos artigos in vitro e in vivo. Para os estudos in vitro foi utilizado um recipiente contendo solução salina com uma resistência elétrica que simulava a do corpo humano, onde foram testados 10 tipos de equipamentos odontológicos nos DCEI, com polaridades, sensibilidades e distâncias variadas. Dentre os equipamentos odontológicos avaliados na revisão sistemática e nos dois estudos in vitro, o amalgamador, a cadeira odontológica, a escova elétrica, a peça de mão, o teste elétrico pulpar, a unidade radiográfica, o laser endodôntico, o motor de implante, o motor endodôntico, o ultrassom piezoelétrico, o microscópio e o termoinjetor não causaram IEM nos DCEI. Entretanto, a cuba ultrassônica, o bisturi elétrico, a diatermia, o fotopolimerizador, o localizador apical, o termocompactador e o ultrassom magnetostricção causaram algum tipo de IEM, que variou de acordo com a marca do equipamento odontológico, distância, polaridade e sensibilidade do DCEI. Baseado nos resultados desse estudo, verificou-se que o amalgamador, a cadeira odontológica, a escova elétrica, a peça de mão, o teste elétrico pulpar, a unidade radiográfica, o laser endodôntico, o motor de implante, o motor endodôntico, o microscópio, o termoinjetor e o ultrassom piezoelétrico não causam IEM nos DCEI. Embora, nenhum equipamento tenha causado dano permanente aos DCEI, os localizadores apicais, o termocompactador, o bisturi elétrico e o fotopolimerizador devem ser utilizados com cautela. Ademais, sugere-se que se evite o uso da cuba ultrassônica, diatermia e ultrassom magnetostricção. (AU)

The cardiovascular implantable electronic devices (CIED) are routinely used in treatment of cardiovascular diseases, especially in elderly population. These devices are subject to electromagnetic interference (EMI) caused by electronic equipment. Thus, this study aimed to evaluate the EMI caused by dental device in CIED (pacemaker - PM and implantable cardiac defibrillator - ICD). Thus, three papers were outlined: a systematic literature review and two in vitro studies. In the systematic review was carried out searches on electronic databases, using MeSH (Medical Subject Headings) terms to identify potentially relevant studies. We included articles in vitro and in vivo. For the in vitro studies we used a vessel with saline solution to simulate the electrical resistance of the human body, where were tested 10 types of dental device in CIED with different polarities, sensitivities and distances. Among the dental device evaluated in systematic review and two in vitro studies, the amalgamator, dental chair, electric toothbrush, handpiece, electric pulp test, radiographic unit, endodontic laser, dental implant motor, endodontic motor, microscope, heated injector and piezoelectric ultrasound unit did not cause EMI in CIED. However, the ultrasonic bath cleaner, electrosurgical unit, diathermy, curing, apex locator, thermocompactor and ultrasonic device caused some type of EMI, which varied according to the brand of dental device, distance, polarity and sensitivity of CIED. It is concluded that: no dental device caused permanent damage to CIED. Based on the results of this study, it was found that the amalgamator, dental chair, electric toothbrush, the handpiece, the electric pulp test, radiographic unit, endodontic laser, dental implant motor, endodontic motor, microscope, heated injector and the piezoelectric ultrasound unit does not cause EMI in CIED. Although, no equipment has caused permanent damage to DCEI, the apex locators, thermocompactor, electrosurgical unit and curing light should be used with caution. Furthermore, it is suggested to avoid the use of the magnetostriction ultrasonic unit and diathermy. (AU)

Desinfecção do sistema de água de equipamentos odontológicos com clorexidina / Disinfection of dental unit waterline with chlorexidine

Introdução: A água utilizada em procedimentos odontológicos pode apresentar- se contaminada, sendo fonte de infecção para profissionais e pacientes. Objetivo: Comparar a efetividade da clorexidina 0,1% e do hipoclorito de sódio 1% na desinfecção do sistema de água de equipamentos odontológicos. Método: Três equipamentos odontológicos sofreram desinfecção com clorexidina; e três, com hipoclorito de sódio mediante acionamento da seringa tríplice durante dois minutos. Amostras de água coletadas antes, após a desinfecção e no final do dia foram analisadas microbiologicamente. Amostras do filtro de abastecimento também foram analisadas. Resultados: As amostras coletadas antes da desinfecção mostraram altos níveis de contaminação (>500 UFC/ml). Após emprego dos desinfetantes, estas apresentaram-se nos padrões recomendados pela American Dental Association – ADA (<200 UFC/ml). A água do filtro de abastecimento também estava dentro dos limites estabelecidos pela ADA. Conclusão: Clorexidina 0,1% mostrou-se tão efetiva quanto hipoclorito de sódio 1% na desinfecção do sistema de água de equipamentos odontológicos.

Introduction: The water used in dental procedures may be contaminated and source of infection for patients and dental staff. Objective: The aim of this study was to compare the effectiveness chlorhexidine 0.1% and sodium hypochlorite 1% in the disinfection of dental unit waterline. Method: Three dental units were disinfection with chlorhexidine and three with sodium hypochlorite by flushing the triple syringe for two minutes. Water samples collected before and after disinfection and in the end of the day were analyzed microbiologically. Samples of the supply filter were also analyzed. Results: Samples collected before disinfection showed high levels of contamination (> 500 CFU / ml). After use of disinfectants, the samples were within the recommended standards by the American Dental Association – ADA (< 200 CFU / ml). The water supply filter was also within the limits established by the ADA. Conclusion: Chlorhexidine 0.1% was effective as sodium hypochlorite 1 % for the disinfection of dental unit waterlines.

Accuracy of five electronic foramen locators with different operating systems: an ex vivo study

Objective: The aim of this study was to evaluate, ex vivo, the precision of five electronic root canal length measurement devices (ERCLMDs) with different operating systems: the Root ZX, Mini Apex Locator, Propex II, iPex, and RomiApex A-15, and the possible influence of the positioning of the instrument tips short of the apical foramen. Material and Methods: Forty-two mandibular bicuspids had their real canal lengths (RL) previously determined. Electronic measurements were performed 1.0 mm short of the apical foramen (-1.0), followed by measurements at the apical foramen (0.0). The data resulting from the comparison of the ERCLMD measurements and the RL were evaluated by the Wilcoxon and Friedman tests at a significance level of 5%. Results: Considering the measurements performed at 0.0 and -1.0, the precision rates for the ERCLMDs were: 73.5% and 47.1% (Root ZX), 73.5% and 55.9% (Mini Apex Locator), 67.6% and 41.1% (Propex II), 61.7% and 44.1% (iPex), and 79.4% and 44.1% (RomiApex A-15), respectively, considering ±0.5 mm of tolerance. Regarding the mean discrepancies, no differences were observed at 0.0; however, in the measurements at -1.0, the iPex, a multi-frequency ERCLMD, had significantly more discrepant readings short of the apical foramen than the other devices, except for the Propex II, which had intermediate results. When the ERCLMDs measurements at -1.0 were compared with those at 0.0, the Propex II, iPex and RomiApex A-15 presented significantly higher discrepancies in their readings. Conclusions: Under the conditions of the present study, all the ERCLMDs provided acceptable measurements at the 0.0 position. However, at the -1.0 position, the ERCLMDs had a lower precision, with statistically significant differences for the Propex II, iPex, and RomiApex A-15.

Study of the antimicrobial efficacy of chlorhexidine in dental unit water: evaluation of microbial contamination in the dental office / Estudo da capacidade antimicrobiana da clorexidina na água do equipamento odontológico: avaliação de contaminação microbiana em ambiente odontológico

Objective: The aim of this study to count anaerobic bacteria before and after the use of dental equipment and to study the influence of chlorhexidine on the dental unit reservoir water. Methods: Sterile swabs were used to collect bacterial samples from the cuspidor, lights, syringes, low-and high speed handpieces and dental chairs (arms and backrest) before and after the placement of barriers. Blood agar plates were placed on the patient's and dentist's forehead and by the patient's nose and shoulder and exposed to aerosoils without (group 1) and with 0,5% (group 2) and 1,0% (group 3) chlorhexidine generated by the high speed handpiece. Ten aerosol samples were collected for each group. A sample of 1mL of the dental unit reservoir water was collected before and after the use of the high speed handpiece. The anaerobic bacterial counts were compared by the Wilcoxon and Kruskal-Wallis tests. Results: The contamination of the high speed handpiece (p=0,0431) and cuspidor (p=0,0117) increased significantly after use. Contamination in the dental unit reservoir water also increased significantly after use of the high speed handpiece. The most contaminated area was the patient's nose. Conclusion: The addition of 0,5% and 1,0% chlorhexidine in the dental office sifnificantly.

ObjetivoO objetivo deste estudo foi quantificar as bactérias anaeróbicas, antes e após o uso deequipamentos odontológicos e estudar a influência da clorexidina na água doreservatório.MétodosOs seguintes itens foram avaliados: cuspideira, luzes, seringas, baixa e alta rotação,braço da cadeira e do encosto com coleções realizadas antes e após a colocação debarreiras. A contaminação microbiana causada pelos aerossóis de alta rotação tambémfoi avaliada: Grupo 1 (controle): (100%) de água no reservatório; Grupo 2: água noreservatório contendo 0,5% de clorexidina, Grupo 3: água no reservatório contendo1,0% de clorexidina. Dez amostras de aerossol foram recolhidos a partir de cadagrupo: placas de ágar-sangue foram colocadas na testa do paciente e do dentista e nonariz e ombro do paciente. Amostra de 1mL a partir do conteúdo da água no reservatóriofoi medida antes e após a utilização de alta rotação. Comparações entre bactériasanaeróbias foram feitas com o uso de Wilcoxon e Kruskal-Wallis teste estatístico.ResultadosVerificou-se um aumento significativo na contaminação antes e após o procedimentoutilizando alta rotação (p=0,0431) e na cuspideira (p=0,0117). Foi possível observarum aumento significativo de contaminação microbiana na água do reservatório, apósa sua utilização. O nariz do paciente era a área mais afetada.ConclusãoA adição de 0,5% e 1,0% de clorexidina no reservatório representa uma reduçãosignificativa de contaminação microbiana gerado no ambiente de um consultório odontológico.

A dinâmica inovativa do subsistema de base mecânica, eletrônica e de materiais / The innovative dynamic of the mechanics, electronics and materials subsystem / La dinámica innovadora del subsistema de base mecánica, electrónica y de materiales

O subsistema de base mecânica, eletrônica e de materiais, um dos subsistemas do complexo produtivo da saúde, reúne diferentes atividades, usualmente agregadas na designada indústria de equipamentos e materiais médico-hospitalares e odontológicos, uma área estratégica para a saúde por representar uma fonte contínua de mudanças nas práticas assistenciais. Além de exercer influência na prestação de serviços de saúde, possui potencial de promover o adensamento do sistema nacional de inovação e de ampliar a competitividade da indústria como um todo, dado que articula tecnologias portadoras de futuro. Apesar do crescimento significativo dessa indústria no Brasil nos últimos anos, esses equipamentos e materiais têm apresentado um crescente déficit na balança comercial. Essa incompatibilidade entre as necessidades nacionais de saúde e a base produtiva e inovativa da indústria aponta fragilidades estruturais do subsistema. Utilizando o arcabouço da economia política, o objetivo do artigo foi discutir o desenvolvimento dessa indústria no Brasil e seus desafios.

The mechanics, electronics and materials subsystem, one of the subsystems of the health care productive complex, encompasses different activities, usually clustered in what is called the medical, hospital and dental equipment and materials industry. This is a strategic area for health care, since it represents a continuous source of changes in care practices, and influences the provision of health care services. It has, moreover, potential for promoting the progress of Brazil's system of innovation and for increasing the competitiveness of the industry as a whole, given that it articulates future technologies. Despite the significant growth of this industry in Brazil in recent years, such equipment and materials have been presenting a growing deficit in the balance of trade. This incompatibility between national health care needs and the productive and innovative basis of the industry points to structural fragilities in the system. Using the framework of political economy, the article aims to discuss the development of this industry in Brazil and its challenges.

OBJETIVO: El subsistema de base mecánica, electrónica y de materiales, uno de los subsistemas del complejo productivo de la salud, reúne diferentes actividades, usualmente agregadas en la designada industria de equipos y materiales médico-hospitalarios y odontológicos, un área estratégica para la salud por representar una fuente continua de cambios en las prácticas asistenciales. Además de ejercer influencia en la prestación de servicios de salud, posee potencial de promover la saturación del sistema nacional de innovación y de ampliar la competitividad de la industria como un todo, dado que articula tecnologías portadoras de futuro. A pesar del crecimiento significativo de esta industria en Brasil en los últimos años, los equipos y materiales han presentado un creciente déficit en la balanza comercial. Esta incompatibilidad entre las necesidades nacionales de salud y la base productiva e innovadora de la industria señalan fragilidades estructurales del subsistema. Utilizando el armazón de la economía política, el objetivo del artículo fue discutir el desarrollo de ésta industria en Brasil y sus desafíos.